CAT Fault Codes FMI DTC

CAT Fault Codes FMI DTC list
0 “High”
1 “Low”
2 “Erratic, Intermittent, or Incorrect”
3 “Voltage Above Normal”
4 “Voltage Below Normal”
5 “Current Below Normal”
6 “Current Above Normal”
7 “Not Responding Properly”
8 “Abnormal Frequency, Pulse Width, or Period”
9 “Abnormal Update Rate”
10 “Abnormal Rate of Change”
11 “Other Failure Mode”
12 “Failure”
13 “Out of Calibration”
14 “Special Instruction”
19 “Data Error”
20 “Data Drifted High”
21 “Data Drifted Low”
FMI 00″High”. If an input is still functioning in the valid range but the input is sending a signal that is above the acceptable limit of the parameter, an FMI 00 code will be generated. On Cat ® Data Link event codes are normally used for this condition.
FMI 01″Low”. An input that is still functioning in the valid range but sending a signal below the acceptable limit of the parameter will cause the FMI 01 code. On Cat ® Data Link event codes are normally used for this condition.
FMI 02″Erratic, Intermittent, or Incorrect”. Erratic or intermittent data includes all measurements that change at a rate that is not considered possible in the real world condition and must be caused by improper operation of the measuring device or the connection to the ECM / ECU module. Signal data from a component is present, at least intermittently. The signal is either unstable or invalid as
recognized by the control doing diagnostics. Data can be correct sometimes and not at other times.
FMI 02 is also used for data that is invalid, such as an invalid state of a parity switch. Note: FMI 02 is different from FMI 10. FMI 02 is used for situations where the rate of change is not physically possible. FMI 10 is used for situations where the rate of change is physically possible, but outside the predefined limits of a properly functioning system.
FMI 03″Voltage Above Normal”. FMI 03 occurs when the voltage reading from the identified circuit is above the valid range. FMI 03 most often relates to a signal circuit.
FMI 04″Voltage Below Normal”. FMI 04 occurs when the voltage reading from the identified circuit is below the valid range. FMI 04 most often relates to a signal circuit.
FMI 05″Current Below Normal”. FMI 05 occurs when the current through the identified circuit is below the valid range. FMI 05 most often relates to a driver circuit.
FMI 06″Current Above Normal”. FMI 06 occurs when the current through the identified circuit is above the valid range. FMI 06 most often relates to a driver circuit.
FMI 07″Not Responding Properly”. FMI 07 occurs when an electronic control sends an electrical command to a mechanical system and the result is not within the acceptable range. An example of
FMI 07 occurs when the ICM transmission (EPTC II) is shifting slowly as a result of a sluggish solenoid valve.
FMI 08″Abnormal Frequency, Pulse Width, or Period”. FMI 08 occurs when a frequency of the signal or the pulse width of the signal is not within the range that is expected.
Note: The period is the time in seconds for one cycle at a specific frequency.
FMI 09″Abnormal Update Rate”. FMI 09 pertains to the communication between the electronic controls on the data link. FMI 09 occurs when an electronic control is not able to receive any information from another electronic control, when the electronic control expects to receive information.
FMI 10″Abnormal Rate of Change”. FMI 10 relates to a signal that changes too fast or too slow. The rate of change is outside of the expected limit, but possible in the real world.
FMI 11″Other Failure Mode”. FMI 11 occurs when the electronic control identifies more than one
FMI as being responsible for a single problem, or when the failure mode does not properly fit into any other FMI.
FMI 12″Failure”. FMI 12 occurs when a smart device (such as an ECM / ECU) has determined that a device has failed.
Note: In the past, FMI 12 had also been used to describe the following conditions:
• An electronic control sends a signal to another electronic module over a data link. The electronic control expects a response but the electronic control receives no response or an incorrect response.
• An electronic control expects to receive information on a continuing basis from another
electronic module over a data link, but not all expected information is received.
FMI 13″Out of Calibration”. FMI 13 occurs when calibration is required. Either the calibration has never been performed or the system has gone out of calibration.
FMI 14″Special Instruction”. FMI 14 is used when a special procedure or more detailed information is required to understand it.
FMI 19″Data Error”. FMI 19 is associated with network data that is received. The component that is used to measure the real world signal is wired directly to the module that is sourcing the data to the network. The module that is receiving the data via the network is receiving the information with an error indicator, and not the actual data. FMI 20″Data Drifted High”.
FMI 21″Data Drifted Low”.