Valtra Tractor logo
Valtra Tractor logo

VALTRA Tractor Fault Codes DTC

If the display unit shows a fault code:
Measures:

VALTRA Tractor Fault Codes DTC

  1. Decode the fault code according to instr. 370/5 —6 (self —diagnosis)
  2. Check the function of the component in the test modet (instr. 370/8).
  3. Repair the fault.
  4. If the control unit A1A or programs have been changed, make necessary settings according to instr.
    370/24A.
  5. Carry out all points in the test mode (instr. 370/8). This ensures, that the tractor is OK before delivery.
    From ser. no.
    K41107 — incl: Check in the fault code memory F1.
  6. Test — run the tractor according to instr. 370/24E.
    — If the display does not show the fault code:
    In the table below, there are faults which have not the fault codes:
    Component: Possible reason: Measures:
  7. AC 5 display unit does not function (on the LH side pillar)
    — control unit A1 supply voltage or earth has malfunctions or the display supply.
    — display unit P6 faulty
    — control unit connector A1A1 loose
    — check fuse F24
    — voltage measures from control unit A1
    connectors A1A1/1 – A1A1/2 (=battery voltage)
    — new display unit, if the system does not function
    — check connections
  8. In the dashboard there is lit “P”, although the driving direction has been selected
    — shuttle lever switch S15 (P) faulty or
    wrongly fitted.
    — testing in the test mode, point d16 / d22
    — 1)
    — check the fitting of switch S15 (page 370 —20)
  9. Black arrow is blinking, although the driving direction has been selected
    — driver has left the seat over 4 (6) seconds. AC 5.2: over 30 sec., when the clutch pedal is depressed.
    — detector switch S60 (in the seat) does not function or wire damage
    — on the seat, shuttle lever to position P, shuttle lever to the driving position
    — testing in the test mode, point d05, 2)
  10. Black arrow does not change, when using the shuttle lever
    — shuttle lever switch S40 (F) or S41 (R) faulty or loosed in the frame.
    — testing in the test mode, points d09, d10 / d18, d19
  11. Shuttle, DPS or PTO have malfunctons (e.g. function is slow) — fault, that the control unit A1 has not identified
    — pressure in the low pressure circuit too low
    — clutch pre —fillling or initial pressure indexes are wrongly set
    — carry out all procedures in the test mode (instr. 370/8)
    — low hydraulics pressure measuring, see instr no. 911 —1
    — check indexes / in the setting mode,
    (instr. 370/24D, AC5.2: instr. 371/11.)
  12. Engine does not start (starter motor does not rotate) Tractors J38343 —.
    — no supply to control unit A1.
    — Parking brake switch S15 or input signal A1A4/14 (AC 5) or A1A8/8 (AC 5.2) faulty
    — Control unit output signal A1A2/3 (AC
    5) (to relay K28) or A1A3/5 (AC 5.2) faulty.
    — check fuse F24
    — testing in test mode, point d16/d22 (if necessary, change switch or control unit)
    — Check whether the voltage from control unit A1 is in relay K28 (when necessary, change the control unit).

F7 Direction information (rpm) *)
F6 PTO speed (rpm) *)
F5 Shuttle output speed (rpm) *)
F4 Shuttle output speed (rpm) *)
F3 Reserve
F2 Driving speed *)
F1 Engine speed *)
A4 Clutch pedal position %
A3 Gas pedal position *) %
A2 Gearbox temperature
A1 Outdoor temperature
d16 Parking brake
d15 PTO standby button
d14 Seat direction (only TwinTrac)
d13 PTO —speed 2 (lever in rear position)
d12 PTO —speed 1 (lever in front position)
d11 DPS pre —programming button (under
shuttle lever)
d10 Direction R (rearwards)
d09 Direction F (forwards)
d08 DPS auto/man
d07 DPS auto1/auto 2
d06 Clutch pedal limit switch
d05 Driver detection (in seat) 1)
d04 PTO start
d03 HiShift buttons
d02 DPS push button, down
d01 DPS push button, up e.g. 5142 START LEVEL
Program version nummer
P1 DPS solenoid 1 (clutch C1) *)
P2 DPS solenoid 2 (clutch C2) *)
P3 DPS solenoid 3 (clutch C3) *)
P4 F clutch solenoidi (forwards) *)
P5 R clutch solenoid (rearwards) *)
b Counter functions