FENDT Fault Codes DTC

0.0.11 A021;
A022
ECU, EDC;
ECU, EMR
EDC / EMR bus fault.
Fault in ECU
Tractor can be driven
using accelerator.
Programming errors in
ECU.
Fault message, no
restrictions.
EOL reprogramming
necessary.

0.0.14 A009 Transmission control
unit
Bus fault No functions available,
no display
Power supply for CAN
bus is in circuit board
A013; fuse F040, F041

0.0.16 A001,
A002
Rear PTO Bus fault No functions available,
no display
Power supply for CAN
bus is in circuit board
A013; fuses F040, F041

0.0.18 A005,
A014
Rear EPC Bus fault No functions available,
no display
Power supply for CAN
bus is in circuit board
A013; fuses F040, F041

0.0.1A A002,
Y015,
Y016,
Y017,
Y018,
Y019
ECU, enhanced control,
electric auxiliary control
valves
Bus fault No functions available,
no display
Power supply for CAN
bus is in circuit board
A013; fuses F040, F041

0.0.1F A034 Joystick Joystick bus fault (‘Drive
switch data transfer
fault’)
Emergency operation,
no auxiliary valve
operation
Power supply for CAN
bus is in circuit boardA013; fuse F047 JOYSTICK CAN –
JOYSTICK

0.1.50 A007 Instrument cluster VDO instrument cluster
EEPROM not
programmed
Malfunctions in
instrument cluster
EOL reprogramming
necessary

0.1.55 S036 Hydraulic oil level
sensor
Sensor fault, wiring fault No monitoring ‘Spool valves 1’ circuit
diagram

0.1.57 B006,
A022
Sensor, charge air
temperature,
ECU, EMR
Sensor fault, wiring fault No monitoring Circuit diagram:
“Instrument cluster”
(F400, F700); “EDC
control” (F900); “EMR
engine control (F7/800
Vario)
For EDC/EMR EDC –
level converter /
SERDIA diagnostics

1.1.01,
poss.
B038
or
B055
EDC / EMR foot throttle
rotary position sensor
(yellow), combi-sensor
Signal too high, signal
too low, signal missing
for longer than 2000 ms
Chapter 2000 Reg.B
(EDC fault or EMR fault)
‘EDC Engine control’,
‘EMR Engine control’
circuit diagram
TRANSMISSION,
AUTOMATIC MAXIMUM
OUTPUT CONTROL

1.1.04 A002 ECU, enhanced control Tractor Management
System (TMS)
checksum error
Tractor Management
System (TMS) doesn’t
function
EOL reprogramming
necessary

1.1.7E B035 Hand throttle rotary
position sensor
Signal out of range Restricted operating
mode, Chapter 2000
Reg.B (EDC fault or
EMR fault)
‘EDC Engine control’,
‘EMR Engine control’
circuit diagram
TRANSMISSION,
AUTOMATIC MAXIMUM
OUTPUT CONTROL
8.5 V supply fault Fuse 26

0.0.12 A008 Vario terminal Bus fault No functions available,
no display
Power supply for CAN
bus is in circuit board
A013; fuse F039, F046

0.0.13 A004 Control console Bus fault No functions available,
no display
Power supply for CAN
bus is in circuit board
A013; fuse F040, F041

0.0.15 A001,
A002
4WD engagement;
Diff. lock engagement
Bus fault No functions available,
no display
Power supply for CAN
bus is in circuit board
A013; fuses F040, F041

0.0.17 A001,
A002
Front PTO Bus fault No functions available,
no display
Power supply for CAN
bus is in circuit board
A013; fuses F040, F041

0.0.19 A002 Front power lift Bus fault No functions available,
no display
See Service Training
EPC C
(X990.005.023.026en)

0.0.1B A002 ECU, enhanced control TeachIn bus faulty –
Master (Variotronic TI)
(‘Teach-in data transfer
fault’)
Emergency mode

0.0.1E ECU, Neumaier Bus fault Neumaier
reversing system
Neumaier System
doesn’t work
(Neumaier Service
Manual)

0.0.20 A007 Instrument cluster CAN Bus fault between
A007 instrument cluster
and tractor electronics
No functions available,
no display
Power supply for CAN
bus is in circuit board
A013; fuses F040, F041

0.1.51 B012 Engine oil pressure
sensor
Sensor fault, wiring fault No monitoring ‘Instrument cluster’
circuit diagram
12 V supply fault A013 fuse 24

0.1.54 B019 Compressed air tank
pressure sensor
Sensor fault, wiring fault No display ‘Instrument cluster’
circuit diagram
12 V supply fault A013 fuse 25

0.1.56 B005,
A021,
A022
Temperature sensor
engine temp. (=water),
(ECU,EDC / EMR)
Sensor fault, wiring fault No monitoring ‘Instrument cluster’
circuit diagram

0.1.59 B007;
B034
Fuel level sensor Sensor fault, wiring fault No display ‘Instrument cluster’
circuit diagram

1.1.03 B029,
B038
or
B055
EST foot throttle rotary
position sensor EST
(red), EDC foot throttle
rotary position sensor
(yellow), combi-sensor
B029 and B038 do not
match, no match B055 –
combi-sensor (PIN 3 to
PIN 6)
Restricted operating
mode, Chapter 2000
Reg.B (EDC fault or
EMR fault)
‘EDC Engine control’,
‘EMR Engine control’
circuit diagram
TRANSMISSION,
AUTOMATIC MAXIMUM
OUTPUT CONTROL,
calibration code ‘4005’

1.1.05 A021;
A022
EDC control module Engine configuration
could not be read from
the EDC / EMR – control
unit
TMS is disengaged ‘EDC Engine control’,
‘EMR Engine control’
circuit diagram

1.1.7F A004 Control console Electrical fault in hand
throttle memory keys
(EDC/EMR). No
communication with
control console.
Last speed setting is
retained. Engine speed
can be changed using
hand throttle or
accelerator.
JOYSTICK, CANJOYSTICK