kubota-logo
kubota-logo

KUBOTA Excavator & Tractor Fault Codes DTC

Kubota-M108X-V3800-Tractor-Engines-Fault-Codes-DTC

KUBOTA Excavator Fault Codes DTC

E0105 – Throttle valve, short to battery
L0102 – Light button, erroneous activation
E0106 – Throttle valve shorted to ground
L0202 – High feed button, erroneous activation
E0107 – Throttle valve open circuit
L0302 – Auxiliary hydraulics button, erroneous activation
L0402 – Information button, erroneous activation
E0123 – Throttle valve not adjusted
L7404 – No communication with gateway controller
E0321 – 5V supply out of range (high value)
E0322 – 5V supply out of range (low value)
L7672 – Left panel programming error
E0421 – Throttle sensor out of range (high value)
E0422 – Throttle sensor out of range (low value)
M0216 – Hydraulic filter not connected
M0217 – Hydraulic filter clogged
E0521 – Throttle valve feedback out of range (high value)
E0522 – Throttle valve feedback out of range (low value)
M0309 – Battery voltage low
M0310 – Battery voltage high
E3128 – Power off error, log only
M0311 – Battery voltage extreme high
M0314 – Battery voltage limit low
E3297 – Controller programmed, log only
M0322 – Battery voltage is below the maximum permissible
M0414 – Engine oil pressure extremely low
M0415 – Engine oil pressure at emergency level turning off the engine
H2521 – Blade angle control lever switch signal above the maximum permissible
H2522 – Blade angle control lever switch signal below the maximum permissible
H2524 – Blade angle control lever switch signal behind outside the neutral value
M0610 – Engine speed high
M0611 – Extremely high engine speed
H2605 – Blade angle base solenoid short to battery
M0613 – No engine speed signal
H2606 – Blade angle base solenoid short to ground
M0615 – Engine speed at emergency shutdown level engine
H2607 – Blade angle base solenoid circuit open
M0618 – Engine speed out of range
H2632 – Blade angle base solenoid, overcurrent
H2705 – Blade angle rod solenoid short to battery M0710 Hydraulic oil temperature high
H2706 – Blade angle rod solenoid short to ground
M0711 – Extremely high hydraulic oil temperature system
H2707 – Blade angle rod solenoid circuit open
M0715 – Hydraulic oil temperature at level emergency engine shutdown
H2732 – Blade angle rod solenoid, overcurrent
M0721 – Hydraulic oil temperature is higher maximum permissible
M0722 – Hydraulic oil temperature is lower maximum permissible
H3128 – Recovery mode failure
M0810 – Engine coolant temperature high
H4423 – Secondary controller not programmed
M0811 – Coolant Temperature Extremely High engine
H4497 – Secondary controller programmed
M0815 – Engine coolant temperature at level emergency engine shutdown
M0821 – Engine coolant temperature is higher maximum permissible
H4621 – Sensor supply voltage 5 V, out of range, high meaning
M0822 – Engine coolant temperature is lower maximum permissible
H4622 – Sensor supply voltage 5 V, out of range, low meaning
M0216 – Hydraulic filter not connected
H7404 – No communication with main controller
H7604 – No communication with display

M0909 – Fuel level low
M2721 – Throttle sensor out of range (high value)
M0921 – Fuel level is above the maximum permissible
M2722 – Throttle sensor out of range (low value)
M0922 – Fuel level below the maximum permissible
M3128 – Recovery mode failure
M1121 – Console sensor out of range (high value)
M1122 – Console sensor out of range (low value)
M3204 – No communication with throttle controller
M1128 – Console sensor failure
M3304 – No connection with Deluxe panel
M1305 – Fuel hold solenoid shorted to battery
M1306 – Fuel hold solenoid shorted to ground
M3404 – No communication with RFID key controller
M1307 – Fuel hold solenoid circuit open
M3702 – Hydraulic transmission, faulty activation
M1402 – Fuel retraction solenoid output, erroneous activation
M3703 – Hydraulic transmission, faulty shutdown
M1403 – Fuel pull solenoid output, erroneous shutdown
M1407 – Fuel retraction solenoid output circuit open
M1428 – Fuel Pull Solenoid Output Failure
M4109 – Generator speed low
M1705 – Hydraulic activation solenoid shorted to battery M4110 Generator high speed
M1706 – Hydraulic activation solenoid shorted to ground
M1707 – Hydraulic activation solenoid circuit open
M4304 – No communication with keypad
M1732 – Hydraulic activation solenoid, overcurrent
M4404 – No communication with secondary controller
M2005 – Two speed solenoid shorted to battery
M2006 – Two-speed solenoid shorted to ground
M4621 – Sensor supply voltage 5 V, out of range, high meaning
M2007 – Two-speed solenoid circuit open
M4622 – Sensor supply voltage 5V, out of range, low meaning
M2102 – Glow plug output, faulty switching on
M4721 – Sensor supply voltage 8 V, out of range, high meaning
M2103 – Glow plug output, erroneous shutdown
M4722 – Sensor supply voltage 8 V, out of range, low meaning
M2107 – Glow plug output circuit open
M2128 – Glow plug output failure
M5002 – Incorrect activation of lighting output
M5003 – Incorrect lighting output switch off
M2202 – Incorrect starter activation
M2203 – Incorrect starter shutdown
M5205 – Base bias solenoid shorted to battery
M2207 – Starter output circuit open
M5206 – Bias base solenoid shorted to ground
M2228 – Starter output failure
M5207 – Base bias solenoid open circuit
M5232 – Main bias solenoid, overcurrent
M2302 – Starter relay, faulty activation
M2303 – Starter relay, faulty shutdown
M5305 – Bias rod solenoid, erroneous activation
M5306 – Bias rod solenoid shorted to ground
M2402 – Fuel pull solenoid relay, faulty activation
M5307 – Bias rod solenoid open circuit
M2403 – Fuel pull solenoid relay, erroneous shutdown
M5332 – Bias Rod Solenoid, Overcurrent
M2521 – Load pressure sensor over limit M5421 Offset control switch over limit acceptable
M2522 – Load Pressure Sensor Below Limit M5422 Bias Control Switch Below Limit acceptable
M5424 – Offset control switch outside neutral value
M2602 – Glow plug relay, faulty activation
M2603 – Glow plug relay, erroneous shutdown