New-Holland-logo
New-Holland-logo

NEW HOLLAND Tractor Fault Codes DTC

NEW HOLLAND & CASE IH Tractors Fault Codes DTC

ADIC Codes

[ADIC] – 1 – Processor memory error (EEPROM checksum error)
[ADIC] – 11 – Fuel tank level sensor B2/1 signal faulty (short circuit to earth)
[ADIC] – 20 – Pressure sensor B3 signal faulty (line interruption or short circuit to +12 V)
[ADIC] – 250 – CAN Bus OFF

ARU Codes

[ARU] – 1 – Processor error (register test)
[ARU] – 10 – Receipt message from AUX1 was not obtained correctly following reprogramming from 0 to 1
[ARU] – 11 – Receipt message from AUX2 was not obtained correctly following reprogramming from 0 to 2
[ARU] – 12 – Receipt message from AUX3 was not obtained correctly following reprogramming from 0 to 3
[ARU] – 13 – Receipt message from AUX4 was not obtained correctly following reprogramming from 0 to 4
[ARU] – 14 – Receipt message from AUX5 was not obtained correctly following reprogramming from 0 to 5
[ARU] – 15 – Receipt message from AUX6 was not obtained correctly following reprogramming from 0 to 6
[ARU] – 16 – Receipt message from AUX7 was not obtained correctly following reprogramming from 0 to 7
[ARU] – 17 – Receipt message from AUX8 was not obtained correctly following reprogramming from 0 to 8
[ARU] – 2 – Processor error (flash memory)
[ARU] – 20 – Supply voltage too low (< 8 V) [ARU] – 21 – Supply voltage too high (> 18 V)
[ARU] – 30 – Signal from AUX stick with catch (AUX1) below permissible range
[ARU] – 31 – Signal from AUX stick with catch (AUX1) above permissible range
[ARU] – 32 – Signal from AUX stick without catch (AUX2) below permissible range
[ARU] – 33 – Signal from AUX stick without catch (AUX2) above permissible range
[ARU] – 34 – Signal from AUX stick (AUX3) below permissible range
[ARU] – 35 – Signal from AUX stick (AUX3) above permissible range
[ARU] – 36 – Signal from hand throttle lever below permissible range
[ARU] – 37 – Signal from hand throttle lever above permissible range
[ARU] – 38 – Signal from cruise control ON/OFF button below permissible range
[ARU] – 39 – Signal from cruise control ON/OFF button above permissible range
[ARU] – 40 – Signal from + button below permissible range
[ARU] – 41 – Signal from + button above permissible range
[ARU] – 42 – Signal from finger wheel below permissible range
[ARU] – 43 – Signal from finger wheel above permissible range
[ARU] – 5 – Processor error (data memory)
[ARU] – 71 – CAN Bus OFF

AUX Codes

[AUX1] – 11 – Missing receipt message 1 default
[AUX1] – 12 – Missing receipt message 2 configuration
[AUX1] – 13 – Implausible receipt message 1 default
[AUX1] – 14 – Implausible receipt message 2 configuration
[AUX1] – 15 – Incorrect CAN message
[AUX1] – 16 – Processor error (EEPROM inconsistent)
[AUX1] – 17 – A neutral command is awaited following a CAN error
[AUX1] – 21 – Supply voltage too low (< 8.2 V) [AUX1] – 22 – Supply voltage too high (> 18 V)
[AUX1] – 23 – Spool deflection too small
[AUX1] – 24 – Spool deflection too great
[AUX1] – 25 – Float not achieved
[AUX1] – 26 – Spool position amended manually

ECCU Codes

[ECCU3] – 100 – +12 V supply voltage too high (> 16 V)
[ECCU3] – 1 – Processor memory error
[EDC] – 22 – Signal for angle-of-rotation sensor is faulty
[EDC] – 23 – The signal for R6/1 SET POINT potentiometer exceeds the permissible range
[EDC] – 26 – EDC D+ signal not present
[EDC] – 28 – EDC CAN bus message not received by ECCU
[EDC] – 31 – Signal from right force sensor B10/2 is faulty
[EDC] – 32 – Signal from left force sensor B10/1 is faulty
[EDC] – 38 – External pressure sensor not connected
[EDC] – 41 – Signal from radar sensor B16 is faulty or not present
[EDC] – 42 – Theoretical speed signal is incorrect or not present
[EDC] – 43 – Rotation angle sensor not calibrated

EEM Codes

[EEM3] – 100 – Boost pressure sensor, signal voltage too low
[EEM3] – 10 – EEPROM error
[EEM3] – 101 – Boost pressure sensor, signal voltage too high
[EEM3] – 102 – Boost pressure too low
[EEM3] – 103 – Boost pressure too high
[EEM3] – 104 – Boost pressure, no signal
[EEM3] – 109 – Coolant sensor — temperature, no signal
[EEM3] – 110 – Coolant sensor — temperature, signal voltage too low
[EEM3] – 111 – Coolant sensor — temperature, signal voltage too high
[EEM3] – 112 – Coolant — temperature too high
[EEM3] – 113 – Coolant — temperature alarm
[EEM3] – 114 – Boost air temperature sensor, signal voltage too low
[EEM3] – 115 – Boost air temperature sensor, signal voltage too high
[EEM3] – 116 – Boost air temperature, value too high
[EEM3] – 117 – Boost air temperature sensor, no signal
[EEM3] – 121 – Water in fuel
[EEM3] – 141 – CAN Bus OFF (vehicle bus)
[EEM3] – 143 – CAN Bus OFF (ID module – EEM3)
[EEM3] – 146 – RPM default through FMGR too low
[EEM3] – 147 – RPM default through FMGR too high
[EEM3] – 17 – Battery voltage is far too low
[EEM3] – 172 – Upgrade protection error
[EEM3] – 18 – Battery voltage is far too high
[EEM3] – 19 – Battery voltage, no signal
[EEM3] – 20 – Temperature in engine controller too high
[EEM3] – 21 – Temperature sensor in engine controller, signal voltage too low
[EEM3] – 211 – Supply voltage 1 too low
[EEM3] – 212 – Supply voltage 1 too high
[EEM3] – 215 – Supply voltage 3 too low
[EEM3] – 216 – Supply voltage 3 too high
[EEM3] – 22 – Temperature sensor in engine controller, signal voltage too high
[EEM3] – 221 – Engine electronics self test, internal error 1
[EEM3] – 222 – Engine electronics self test, internal error 2
[EEM3] – 223 – Engine electronics self test, internal error 3
[EEM3] – 23 – Temperature sensor in engine controller, no signal